Pages

Monday, December 7, 2015

Darth Vader voice changer 2.0 (HT8950A)

Introduction

Last June I wrote about a Darth Vader voice changer that I made. Back then I used the Velleman MK171 kit as the electronic part of the voice changer. Although it worked pretty well I felt that some area's needed improvement. First, I couldn't get the pushbuttons mounted on the housing to work making it hard to switch the voice effect. Second, I didn't like the limitations that obviously come with such a kit; you're more or less bound to the design as intended by Velleman.

The HT8950A chip

For this project I wanted to deviate from Velleman's MK171 design and experiment with the HT8950A chip, the heart of the kit. The HT8950A chip from Holtek is a voice modulator that provides two special effects, Vibrato and Robot (pin 2 and 5 respectively). It also provides frequency level shifting enabling the user to shift the frequency up or down (pin 3 and 4 respectively). This is perceived as a higher or lower pitched sound resulting in a 'Darth Vader' type of sound when the frequency is shifted two steps lower. More detail on this can be found in the datasheet of the HT8950A. An external LED connected to the LAMP pin (pin 11) changes it's brightness when the input voice signal changes. Pin 12, the AUDIO, provides the resulting sound that can be amplified.

Breadboard with in the middle the HT8950A. For this chip relatively few components are needed to get te voice modulation to work.
The chip can be acquired by buying the MK171 kit from Velleman. This kit also provides you with a LM386 amplifier however it is cheaper to buy the HT8950A without the other (generic) components from eBay or Aliexpress. If you do so make sure that your supplier of your choice has sufficient positive feedback.

Building it on the breadboard

On the datasheet of the HT8950A (page 5 onward) schematics can be found how to connect the chip. The amplifier of  the schematic on page 5 or 7 can easily be exchanged for another one of your liking. I'll probably use the LM386 because it's cheap and I have several on stock. In order to operate the HT8950A one only needs a couple of generic components (7 resistors, 5 capacitors, an LED and a zener diode) so building it is not too complicated.

First I built the circuit on the breadboard without an amplifier. The HT8950A actually has it's own built-in amplifier consequently connecting a small speaker to AUDIO (pin 12) is sufficient to give an audible sound, though barely. Alternatively a headphone can be used. This is especially useful if your roommates start complaining about the weird noise. Later I also connected a homemade amplifier to the circuit (to my roommates despair). The Robot mode sounds good but while testing the frequency level shifting mode a lot of noise became apparent. Placing a capacitor over pin 8 and 9 (AO and AIN respectively) reduces this noise considerably. Optionally a 25K potentiometer can be placed between the 33K resistor and pin 8 to tune the sensitivity of the microphone or any other sound input.

Although I'm rather pleased with the result. I would like to take this experiment a little further. Next I'll try to further optimize the sound, add the LM386 amplifier and solder the circuit to a perf board. Then I'll either use the plywood housing that I made for the original version or make a lighter one.

Overview of the circuit. The Audio in is coming from an old FM radio (top-left). I'm using a headphone to listen to the modulated sound while keeping my roommates happy.

Schematics of the experiment. The capacitor between AO and AIN varied between 47nF an 220nF to reduce the noise. I found that the 47nF gave the best results.

6 comments:

  1. Hi Eric,
    I was pondering with applying this IC to reduce audio feedback. Is it possible to adjust/ limit the frequency variations to about 5% ?? If not, then it won't be usable, for then the voice input becomes noticeable. Yet, if it can be done, can you please tell me the resistor values I should use.
    Thank you in advance for your good advice, Joh from Chile

    ReplyDelete
  2. Hi Joh, I suspect that you want to use the vibrato function of the chip since this generates and alternating (up and down) frequency on the input signal, right? I haven't done any experiment with this function (I was basically interested in the change of pitch of the input signal). I lack a oscilloscope and therefore cannot measure the frequency variation of the VIB with varying resistor values between OSC1 and OSC2, FVIB. So I'm afraid that I can't give you any advice on this.

    ReplyDelete
  3. Hey Eric I was wondering what type of amplifier you connected to it and it would be nice if you can send me the schematics or diagram of the amplifier and how you connected it to the voice modulator circuit thank you :)

    ReplyDelete
    Replies
    1. Hi bc mek, here is a link to the blog entry that includes the schematics including the amplifier: https://www.blogger.com/blogger.g?blogID=8621512650012927612#editor/target=post;postID=8754778025943426388;onPublishedMenu=overviewstats;onClosedMenu=overviewstats;postNum=2;src=postname

      Also I wrote an instructable of this project that can be found here: http://www.instructables.com/id/Darth-Vader-Chest-Box/

      Delete
  4. Hey Eric I was wondering what type of amplifier you connected to it and it would be nice if you can send me the schematics or diagram of the amplifier and how you connected it to the voice modulator circuit thank you :)

    ReplyDelete
  5. My email is besrat10mekonnen@mail.com thanks again

    ReplyDelete

Note: Only a member of this blog may post a comment.